engineering fundamentals Discussion Forum
Directory | Career | News | Standards | Industrial | SpecSearch®
Home Membership Magazines Forum Search Member Calculators

Materials

Design

Processes

Units

Formulas

Math
 
Welcome to eFunda Message Board
This board has been created to facilitate the sharing of knowledge, experience, and opinions among our fellow engineers and students. When posting a message, we ask you to respect each other and always follow all general rules of publishing in public forums. This board is moderated by eFunda staff and we reserve the rights to remove or modify any inappropriate messages. Thank you!

Search Forum Topic:  
 

Showing Topics 1-30 (of 6231)  Next >>
Topic Started Replies Last Post  PST
New technologies creat the new world 09/21/14 0 09/21/14 06:53
Oilfield WC component repair and heat treat issues 09/18/14 0 09/18/14 07:12
Cylindrical roller bearing additive load effects 09/15/14 0 09/15/14 19:11
Diesel engine bearing rotation prevention methods 09/08/14 0 09/08/14 20:49
Set the needle roller bearing joint attention 09/03/14 0 09/03/14 19:14
Impact forces 08/18/14 0 08/18/14 18:40
Sliding bearing part of failure 08/07/14 0 08/07/14 00:38
Different types of Manometers 07/30/14 0 07/30/14 06:55
I need lewis (tooth) form factor for 25deg pressure angle (spur gear) 01/04/13 2 07/13/14 08:50
Powder Pressing Operation 07/12/14 0 07/12/14 06:19
Mechanical engineering ebooks 06/07/14 2 07/10/14 00:32
Causes of Porosity of Die-Castings and How to Improve Die-Casting 07/02/14 0 07/02/14 23:32
fully clamped plate centrally loaded 06/22/14 3 07/01/14 11:52
Diiferent types of gears 06/21/14 0 06/21/14 10:17
Aluminium Gravity Die Casting Industry 06/17/14 0 06/17/14 22:46
Shear force and bending moment 06/07/14 0 06/07/14 05:33
Products Manufacture By Gravity Casting 06/01/14 0 06/01/14 23:20
Piston seal o-rings make shaft stick 08/25/11 12 05/30/14 03:03
EOT Cranes 05/04/14 1 05/29/14 02:38
load capacity of parallel Channelh over difference spans with different cross bracing 05/28/14 1 05/28/14 09:21
Simply supported beam calculation 05/12/14 3 05/26/14 11:10
General purpose mechanical finite element analysis software 05/05/14 0 05/05/14 07:16
thread relief 09/28/13 2 04/24/14 11:50
A sensor to monitor stress on thread/strength of thread 10/04/13 1 04/24/14 11:41
Swanson School of Engineering uses Simulation...Check out Now... 04/22/14 0 04/22/14 02:00
working principle of manual pallet truck 06/24/13 2 04/11/14 02:37
Austenite state - soft or hard 01/04/14 1 03/27/14 13:13
Diffusivity for mass diffusion 01/29/14 0 01/29/14 06:56
Lincoln Electric Acquired Structural Steel Fabricator 01/19/14 0 01/19/14 17:30
Mesh and mass diffusion 01/19/14 0 01/19/14 10:25
Showing Topics 1-30 (of 6231)  Next >>
Home  Membership  About Us  Privacy  Disclaimer  Contact  Advertise

Copyright © 2014 eFunda, Inc.